how much is a ghost immobiliser uses cutting-edge technology to prevent car theft. This hidden device is not detected by thieves and only starts your engine after a PIN code or app is entered.
It connects to the CAN data network of your vehicle and is weatherproof. It features a service/valet function that lets you temporarily start your vehicle when it is in garage.
Easy to install
The Ghost immobiliser protects your car from key theft or hacking, as well as cloning. It is a PIN code system that is integrated into your vehicle's electronic control unit, making it impossible for thieves to detect. Contrary to traditional immobilisers it doesn't require special keys or sensors, and is completely hidden with no LED indications or signals to give away its presence. It is also a lot less expensive than replacing an ECU or installing an entirely new key fob. It also can lower your monthly insurance premiums.
When installing a Ghost 2 immobiliser, be sure to follow the manufacturer's instructions carefully. This will ensure that the device functions properly and efficiently. Test the system following installation by entering the PIN and then starting the car. Regular testing will enable you to spot any issues in the early stages.
Before beginning the installation, ensure the location of the CAN H and CAN L wires. They are crucial for powering the immobiliser, therefore it is essential that they are connected properly. It is also a good idea to label the wires to make it easier to locate them during the installation process. Once you have identified the locations of these wires, connect them to a permanent 12V power source as well as a grounding point. Make sure to utilize a fuse tap when needed to protect the connections from short circuits or damage.
After connecting the wires neaten the wires using cable ties to guard against alteration. It is also a good idea to cover the wires with insulation tape or heat shrink tubing. This will protect the device from electrical shorts and will extend the life of the device. It's a good idea to test your Ghost 2 immobiliser once the wiring is secured.
In the event that you have to hand over your vehicle, such as for valet parking or servicing for valet parking, the Ghost 2 immobiliser has a service mode that temporarily disables the PIN code sequence. Press the brake pedal and hold the accelerator for a number of presses equal to the first digit in the emergency code. The system will then enter service mode, which is confirmed by flashing the indication signal 5 times.
Change PIN codes quickly
Ghost 2 immobilisers are a great way to protect your car from thieves. It is discreetly installed inside the vehicle and is able to be accessed with a special code. The device communicates with the vehicle ECU via its data bus. It does not rely on radio frequency signals, as alarm systems that are sold on the market or traditional Thatcham immobilisers do. This makes it difficult for thieves to detect the click of an immobiliser relay or add new key fobs. The control unit is hidden within the wiring of the vehicle's dashboard, and isn't physically altered to reset the system.
The ghost 2 immobiliser is connected to your vehicle's CAN Data network. It uses buttons on the steering, door panels and centre console, to create a customisable series of up to twenty button presses, which must be entered to start the engine - similar as a PIN code. This unique system can be reprogrammed and doesn't require cutting wires during installation. You can even put your vehicle in Service or Valet mode to allow it to start for a short time when you give it to a mechanic for work.
The app can also be used to block your PIN code in the event that you've lost your keys, or change it. This feature is particularly useful if you have given your vehicle to someone else to be used as a valet or service, as it stops them from starting your vehicle and taking away without your permission. It's also unnoticeable by professional thieves because it doesn't use radio frequencies or circuit cuts.
Another excellent feature of the ghost 2 immobiliser is its capability to prevent thefts of relays. Relay theft is among the most common methods of car theft. The criminals hack the diagnostic ports of your car, and then alter the signal transmitted by the car's ECU to trick it into believing that a valid car key is present. The traditional immobiliser is able to be bypassed this manner, but with the ghost 2 immobiliser the signal is blocked by the immobiliser before it gets to the ECU.
Simple to use app
Ghost 2 is an immobiliser that is revolutionary. It safeguards your vehicle from key-cloning. It connects to the CAN data network of your vehicle and asking you to enter a pin code before it will start the engine. It also stops thieves from by using signal spoofing or device spoofing, which are both common methods of stealing vehicles.
The system is easy to use and works like an auto alarm that is used in a normal way. Installing the system will allow you to create a unique 20-digit pin code that you must enter before you start the vehicle. This will stop the vehicle being taken away, even when you lose your keys. You can turn off the system using an app on your smartphone.
The ghost is silent, and it does not emit radio frequency signals. It is a discrete weatherproof device that can be positioned anywhere inside your car. It can be concealed under the dash, the steering wheel, or even the door panels. It communicates through the CAN data loop to your ECU and is not affected at all by diagnostic tools used by thieves to locate security systems. It is not affected by jamming devices that spoof codes.
It is a concealed installation that doesn't require any wire cutting or modification to the car it can be utilized as an anti-theft system for all vehicles. Its technology has been proven efficient, and it's in compliance with TASSA Standards. The ghost is a great solution for classic, sports and luxury cars. It can also be used to secure cars that are let out on websites like Turo.
The Autowatch Ghost 2 is the next generation of car immobilisers. The system is inaccessible to thieves and prevents them from starting your vehicle unless they have your PIN or are authorised by the app. It also doesn't emit radio frequencies or other signals that can be detected by scanners. The installation process is simple and quick. The app is easy to navigate and has a user-friendly interface that allows for easy configure and use. It also comes with a GPS tracker that can help police locate and find the vehicle.
Simple to reset
It is possible to secure your vehicle from theft by using an immobiliser ghost 2. It integrates into your vehicle's ECU and creates a security barrier that thieves are unable to breach without the correct pin. The device is also TASSA-verified which means it is recognized by insurance companies. It's an effective device to prevent car theft, and could save you a significant amount of money in the long run.
The Ghost system unlike traditional alarms and immobilisers that require cutting of circuits, is directly connected to the vehicle's CAN data network. It works by using the buttons on your dashboard and the steering wheel. You can create a unique PIN sequence that can be up to 20 presses in length. This PIN has to be entered before the engine can be started the same way as the credit card's PIN. Ghost is unnoticeable to thieves and has no indicators that signal its presence, which makes it the most reliable aftermarket CAN bus immobiliser available on the market currently.
The Ghost system has another advantage that it doesn't transmit radio frequency signals. This means it is not detected by thieves or snatched up. This helps to prevent the cloning of keys and relay attacks, as well as the more popular method of hacking into a car's CAN bus system by scanning for signals from the alarm/immobiliser. In addition, the Ghost system is designed to be completely hidden within your vehicle. There are no lights or signals to indicate its presence.
The system comes with the option of a Transport Mode which disables the Ghost System. This is helpful in situations where you need to temporarily deactivate Ghost, such as when you are transporting or maintaining your vehicle. This mode is not as effective as Service Mode as it doesn't disable the Ghost system when you exceed 31 mph in 15 minutes.
To reset your ghost 2 immobiliser, you will need to have the emergency code, which is available from your installer. It is typically hidden under a scratch-off section on the card that was included with the installation. This emergency code should be secured and stored in a secure location like your wallet at home.